• Gear Box : Double reduction Gear box
• Kettle / Cooker : Multi stage cooker for the conditioning of seeds,
  size 42″ Diameter
• Compressing : Crammer Shaft gives extra Cramming of the seed or cake in the Feed
• Chamber: Vertical Hinged and can very easily be opened for replacement of worms
  or cage bars. This saves a lot of time and labour.
• Steel Fabricated Chamber: Reduces time and labour for relining of Cage Bars.
• Bearings : Heavy duty Ball and Roller bearings are fitted for maximum life and low noise operation
• Shaft Withdrawal : The main Worm Shaft can be withdrawn very easily without disturbing the gear
  section in any way. Pressing worms and collars can be changed without disturbing the main shaft. The thrust
  of the pressure worms is taken upon large spherical roller thrust bearings.
• Cast Iron Bodies : For perfect alignment and stability.
• Easy to install, high yield at low operating cost, capable of extracting oil from all known oil seeds.
• Reduced internal wear and tear
• Best Quality of Oil & Cake.
• Maintenance is less & easy
• Hardened Worm Assembly
• Steel Fabricated Base

All Steel Fabrication & Improved Design
For perfect alignment and stability.

Vertical Hinged 34” Three-section Pressing Box. Entirely eliminates the difficult task of removing box for relining or for replacement of worms, which saves a lot of time and labour.

Steel Casted Chambers
Reduces time and labour for relining of Cage Bars.

Shaft Withdrawal
The main Worm Shaft can be withdrawn very easily without disturbing the gear section in any way and pressure worms and spacing collars can be changed without disturbing the shaft. The thrust of the pressure worm is taken upon a large thrust bearing.

Pressure Cone
The final pressure of the cake is positively controlled by a Pressure Cone which is hard faced.

Cake at Discharge
The cake thickness is controlled by a manually operated hand-wheel which is so simple that the choke gear is independent of the main drive and there is no possibility of a sudden load being placed on expeller motor.

Compressor
The Expeller feed is under automatic control and the seed or meal when entering the Expeller is given a preliminary compression by a small crammer-shaft driven by an automatically tensioned belt which stops when feed is excessive, starting again when the accumulation of feed has been absorbed by the Expeller.

Power
Oil Expeller is 15HP/20HP and for Cooker 3HP.

Gear Box & Lubrication
A double helical gear unit made from most suitable special steel running in oil bath. All shafts run on antifriction bearings. The drive housing is oil tight and dust proof, totally enclosed design and is fitted with two oil level indicators.

Kettle / Cooker
The Steam Kettle is of adequate capacity with 42” dia. two high steam jackets fitted with self controlled mean inlet to prevent overflowing with open steam spray arrangement, safety valve, steam pressure gauge, steam traps and steam valves. The Kettle requires 40-55 kgs. process steam per hour at a pressure of 4-5 kg/cm2.

Capacity
The capacity, however, varies with the material and working conditions. The average capacity is 8/10 tons in first pressing and 5/6 tons in second pressing.

• Gear Box : Double reduction Gear box
• Kettle / Cooker : Multi stage cooker for the conditioning of seeds,
  size 42″ Diameter
• Compressing : Crammer Shaft gives extra Cramming of the seed or cake in the Feed
• Chamber:Vertical Hinged and can very easily be opened for replacement of worms
  or cage bars. This saves a lot of time and labour.
• Steel Fabricated Chamber: Reduces time and labour for relining of Cage Bars.
• Bearings : Heavy duty Ball and Roller bearings are fitted for maximum life and low noise operation
• Shaft Withdrawal : The main Worm Shaft can be withdrawn very easily without disturbing the gear
  section in any way. Pressing worms and collars can be changed without disturbing the main shaft. The thrust
  of the pressure worms is taken upon large spherical roller thrust bearings.
• Cast Iron Bodies : For perfect alignment and stability.
• Easy to install, high yield at low operating cost, capable of extracting oil from all known oil seeds.
• Reduced internal wear and tear
• Best Quality of Oil & Cake.
• Maintenance is less & easy
• Hardened Worm Assembly
• Steel Fabricated Base

All Steel Fabrication and Improved Design.

For perfect alignment and stability.

Vertical Hinged 44” Four-section Pressing Box. 
Entirely eliminates the difficult task of removing box for relining or for replacement of worms, which saves lot of time and labour.

Steel Casted Chambers 
Reduces time and labour for relining of Cage Bars.

Shaft Withdrawal 
The main Worm Shaft can be withdrawn very easily without disturbing the gear section in any way and pressure worms and spacing collars can be changed without disturbing the shaft. The thrust of the pressure worm is taken upon a large thrust bearing.

Pressure Cone 
The final pressure of the cake is positively controlled by a Pressure Cone which is hard faced.

Cake at Discharge 
The cake thickness is controlled by a manually operated hand-wheel which is so simple that the choke gear is independent of the main drive and there is no possibility of a sudden load being placed on expeller motor.

Compressor 
Expeller feed is under automatic control and the seed or meal when entering the Expeller is given a preliminary compression by a small crammer-shaft driven by an automatically tensioned belt which stops when feed is excessive, starting again when the accumulation has been absorbed by the Expeller.

Oil & Cake Discharge Conveyor 
This is fitted along the full length of the Expeller having right and left hand flights to deliver the oil and cake to central points. The drive is from the main Gear box (can be provided at an extra cost).

Power 
Oil Expeller is 30HP and for Cooker 5 HP.

Gear Box & Lubrication 
A double helical gear unit made from most suitable special steel running in oil bath. All shafts run on anti-friction bearings. The drive housing is oil tight and dust proof, totally enclosed design and is fitted with a level indicator.

Kettle / Cooker 
The Steam Kettle is of adequate capacity with 48” dia. three-high steam jackets fitted with self controlled meal inlet to prevent overflowing with open steam spray arrangement, safety valve, steam pressure gauge, steam traps and steam valves. The Kettle requires 100/120 lbs. of
process steam per hour at a pressure of 60 lbs. per square inch.

Capacity 
The capacity varies with the material and working conditions. The average capacity is 14/15 tons
in first pressing and 8/10 tons in second pressing.

• GearBox : Double reduction Gear box
• Kettle / Cooker : Multi stage cooker for the conditioning of seeds
• Chamber :Vertical Hinged and can very easily be opened for replacement of worms or cage bars. This
  saves a lot of time and labour.
• Steel Fabricated Chamber: Reduces time and labour for relining of Cage Bars.
• Bearings : Heavy duty Ball and Roller bearings are fitted for maximum life and low noise operation.
• Compressing : Crammer Shaft gives extra Cramming of the seed or cake in the Feed
• Shaft Withdrawal : The main Worm Shaft can be withdrawn very easily without disturbing the gear
  section in any way. Pressing worms and collars can be changed without disturbing the main shaft. The
  thrust of the pressure worms is taken upon large spherical roller thrust bearings.
• Easy to install, high yield at low operating cost, capable of extracting oil from all known oil seeds.
• Reduced internal wear and tear
• Best Quality of Oil & Cake.
• Maintenance is less & easy
• Hardened Worm Assembly
• Cast Iron Bodies: For perfect alignment and stability.
• Steel Fabricated Base

• Vertical Hinged Chambers: Pressing Box eliminates the difficult task of removing box for replacement of worms.
• Chambers: Reduces time and labour for relining of Cage Bars. The main Shaft of the Expeller is of alloy steel construction, fitted with High Pressure Worms, hard faced, with a highly wear resistant alloy.
• Shaft Withdrawal: The main Worm Shaft can be withdrawn easily without disturbing the gear section. The thrust of the pressure worms is taken upon large spherical roller thrust bearings.
• Gear Box & Lubrication: Triple helical gear unit made from most suitable special steel, running in oil bath. All shafts run on anti-friction bearings. Drive housing is oil tight and dust proof, totally enclosed design and is fitted with level indicator. A self contained lubrication arrangement has been provided.
• Kettle / Cooker: Multistage vertical stack cooker for proper conditioning of the seeds.
• Lower Operation and Maintenance Cost: Due to sturdy construction and stringent quality norms our machines work with higher efficiency and incur lower maintenance costs.
• Premium expelled Oil Quality: Well designed worm assembly and chamber construction ensures superior quality of expelled oil.
• Superior Quality of Cake: The cake quality is excellent and cake produced from the machine is of natural colour without charring or burning effect.

• Chamber: Vertical Hinged and can very easily be opened for replacement of worms or cage bars. This saves a lot of time and labour.
• Steel Fabricated Chamber: Reduces time and labour for relining of Cage Bars.
• Bearings: Heavy duty Ball and Roller bearings are fitted for maximum life and low noise operation.
• Compressing: Crammer Shaft gives extra Cramming of the seed or cake in the Feed
• Shaft Withdrawal: The main Worm Shaft can be withdrawn very easily without disturbing the gear section in any way. Pressing worms and collars can be changed without disturbing the main shaft. The thrust of the pressure worms is taken upon large spherical roller thrust bearings.
• Easy to install, high yield at low operating cost, capable of extracting oil from all known oil seeds.
• Reduced internal wear and tear
• Best Quality of Oil & Cake.
• Maintenance is less & easy
• Hardened Worm Assembly

• Chambers : Reduces time and labour for relining of Cage Bars
• The main Shaft of the Expeller is of alloy steel construction, fitted with High Pressure Worms, hard faced, with a highly wear resistant alloy.
• Shaft Withdrawal : The main Worm Shaft can be withdrawn easily without disturbing the gear section. The thrust of the pressure worms is taken upon large spherical roller thrust bearings.
• Gear Box & Lubrication : An improved triple helical parallel shaft gear unit made from most suitable special steel, running in oil bath. All shafts run on antifriction bearings. Drive housing is
  oil tight and dust proof, totally enclosed design and is fitted with level indicator. Aself contained lubrication arrangement has been provided.
• Kettle / Cooker : Multistage vertical stack cooker for proper conditioning of the seeds.
• Lower Power Consumption: The Selection of motors is done keeping in mind the peak load that could arise due to inconsistent feeding resulting in lower power consumption.
• Premium expelled Oil Quality : Well designed worm assembly and chamber construction ensures superior quality of expelled oil.
• Superior Quality of Cake : The cake quality is excellent and cake produced from the machine is of natural colour without charring or burning effect .
• Retention of oil in Cake : Superior process parameters ensure accurate retention of oil in the cake.