Oil Machine

• GearBox: Double reduction Gear box
• Kettle / Cooker:Multi stage cooker for the conditioning of seeds, size 42" Diameter
• Chamber: Vertical Hinged and can very easily be opened for replacement of worms or cage bars. This saves a lot of time and labour
• Steel Fabricated Chamber: Reduces time and labour for relining of Cage Bars
• Bearings: Heavy duty Ball and Roller bearings are fitted for maximum life and low noise operation
• Compressing: Crammer Shaft gives extra Cramming of the seed or cake in the Feed
• Shaft Withdrawal: The main Worm Shaft can be withdrawn very easily without disturbing the gear section in any way. Pressing worms and collars can be changed without disturbing the main shaft. The thrust of the pressure worms is taken upon large spherical roller thrust bearings
• Easy to install, high yield at low operating cost, capable of extracting oil from all known oil seeds
• Reduced internal wear and tear
• Best Quality of Oil & Cake
• Maintenance is less & easy
• Hardened Worm Assembly
• Cast Iron Bodies: For perfect alignment and stability
• Steel Fabricated Base

Automatic Grade	Automatic, Semi-Automatic
Power (kw)	22.371
Capacity	8 TON / 24 Hour
Chamber	Fabricated Chamber
Power	3 Phase 30 hp Motor

All Steel Fabrication & Improved Design
For perfect alignment and stability.

Vertical Hinged 34" Three-section Pressing Box.
Entirely eliminates the difficult task of removing box for relining or for replacement of worms, which saves a lot of time and labour.

Steel Casted Chambers
Reduces time and labour for relining of Cage Bars.

Shaft Withdrawal
The main Worm Shaft can be withdrawn very easily without disturbing the gear section in any way and pressure worms and spacing collars can be changed without disturbing the shaft. The thrust of the pressure worm is taken upon a large thrust bearing.

Pressure Cone
The final pressure of the cake is positively controlled by a Pressure Cone which is hard faced.

Cake at Discharge
The cake thickness is controlled by a manually operated hand-wheel which is so simple that the choke gear is independent of the main drive and there is no possibility of a sudden load being placed on expeller motor.

Compressor
The Expeller feed is under automatic control and the seed or meal when entering the Expeller is given a preliminary compression by a small crammer-shaft driven by an automatically tensioned belt which stops when feed is excessive, starting again when the accumulation of feed has been absorbed by the Expeller.

Power
Oil Expeller is 15HP/20HP and for Cooker 3HP.

Gear Box & Lubrication
A double helical gear unit made from most suitable special steel running in oil bath. All shafts run on antifriction bearings. The drive housing is oil tight and dust proof, totally enclosed design and is fitted with two oil level indicators.

Kettle / Cooker
The Steam Kettle is of adequate capacity with 42” dia. two high steam jackets fitted with self controlled mean inlet to prevent overflowing with open steam spray arrangement, safety valve, steam pressure gauge, steam traps and steam valves. The Kettle requires 40-55 kgs. process steam per hour at a pressure of 4-5 kg/cm2.

Capacity
The capacity, however, varies with the material and working conditions. The average capacity is 8/10 tons in first pressing and 5/6 tons in second pressing.

Chamber	Fabricated chamber
Power	Oil Expeller is 15hp/20hp and for Cooker 3hp.
Automation Grade	Automatic, Semi-Automatic
Pressure	4-5 kg/cm2
Capacity	8/10 tons in first pressing and 5/6 tons in second pressing

• Chambers: Reduces time and labour for relining of Cage Bars
• The main Shaft of the Expeller is of alloy steel construction, fitted with High Pressure Worms, hard faced, with a highly wear resistant alloy
• Shaft Withdrawal: The main Worm Shaft can be withdrawn easily without disturbing the gear section. The thrust of the pressure worms is taken upon large spherical roller thrust bearings
• Gear Box & Lubrication: An improved triple helical parallel shaft gear unit made from most suitable special steel, running in oil bath. All shafts run on antifriction bearings. Drive housing is oil tight and dust proof, totally enclosed design and is fitted with level indicator. A self contained lubrication arrangement has been provided
• Kettle / Cooker: Multistage vertical stack cooker for proper conditioning of the seeds
• Lower Power Consumption: The Selection of motors is done keeping in mind the peak load that could arise due to inconsistent feeding resulting in lower power consumption
• Premium expelled Oil Quality: Well designed worm assembly and chamber construction ensures superior quality of expelled oil
• Superior Quality of Cake: The cake quality is excellent and cake produced from the machine is of natural color without charring or burning effect
• Retention of oil in Cake: Superior process parameters ensure accurate retention of oil in the cake

Chamber	Two Chambers Each of 36” Long
HP	3 Phase 100 HP Motor
Capacity	50 to 60 Ton (In 24 Hours) in pre-pressing and 25 to 30 Ton in Single & Final crushing

Cooker / Cooking Vessel:

Brief Outstanding Features
Cookers / Heating Kettles are used for proper heating and conditioning of the oil seeds prior to expelling.Controlled heat and moisture open up the oil bearing cells for maximum oil yield.

Construction
These Cookers are all steel fabricated with steam heated jackets for each compartment. These jackets are suitably welded with studs and hydraulically tested before assembly. All compartments except the top one are provided with hinged doors for easy access.

Heating
Steam jackets are indirectly heated by steam and cookers are complete with necessary fittings i.e. valves, pressure gauges, relief valves, steam traps and thermometer. Bottom stage insulation of the Cookers avoids unnecessary heat losses. Insulation can be provided at extra cost.

Moisture Addition
Open steam spray is provided for bottom compartment of smaller cookers and for other sizes at the top and bottom compartments.

Control
Seed temperature, retention time in each stage, moisture content and depth are easily controlled.

Drive
The vertical shaft carries biparted agitators for each compartment and is driven from an independent electric motor through V-Belt and vertical cooled worm type speed reduction gear box.

Steam Consumption
Higher figures are for starting up and the lower figures are for steady running.

All Steel Fabrication & Improved Design
For perfect alignment and stability.

Vertical Hinged 34" Three-section Pressing Box.
Entirely eliminates the difficult task of removing box for relining or for replacement of worms, which saves a lot of time and labour.

Steel Casted Chambers
Reduces time and labour for relining of Cage Bars.

Shaft Withdrawal
The main Worm Shaft can be withdrawn very easily without disturbing the gear section in any way and pressure worms and spacing collars can be changed without disturbing the shaft. The thrust of the pressure worm is taken upon a large thrust bearing.

Pressure Cone
The final pressure of the cake is positively controlled by a Pressure Cone which is hard faced.

Cake at Discharge
The cake thickness is controlled by a manually operated hand-wheel which is so simple that the choke gear is independent of the main drive and there is no possibility of a sudden load being placed on expeller motor.

Compressor
The Expeller feed is under automatic control and the seed or meal when entering the Expeller is given a preliminary compression by a small crammer-shaft driven by an automatically tensioned belt which stops when feed is excessive, starting again when the accumulation of feed has been absorbed by the Expeller.

Power
Oil Expeller is 15HP/20HP and for Cooker 3HP.

Gear Box & Lubrication
A double helical gear unit made from most suitable special steel running in oil bath. All shafts run on antifriction bearings. The drive housing is oil tight and dust proof, totally enclosed design and is fitted with two oil level indicators.

Kettle / Cooker
The Steam Kettle is of adequate capacity with 42” dia. two high steam jackets fitted with self controlled mean inlet to prevent overflowing with open steam spray arrangement, safety valve, steam pressure gauge, steam traps and steam valves. The Kettle requires 40-55 kgs. process steam per hour at a pressure of 4-5 kg/cm2.

Capacity
The capacity, however, varies with the material and working conditions. The average capacity is 8/10 tons in first pressing and 5/6 tons in second pressing.

Automation Grade	Automatic, Semi-Automatic
Power (kw)	11.1855/14.914
Kettle Capacity	40-55 kgs
Pressure Required	4-5 kg/cm2.
Capacity	8/10 tons in first pressing and 5/6 tons in second pressing

• GearBox: Double reduction Gear box
• Kettle / Cooker: Multi stage cooker for the conditioning of seeds
• Chamber: Vertical Hinged and can very easily be opened for replacement of worms or cage bars. This saves a lot of time and labour
• Steel Fabricated Chamber: Reduces time and labour for relining of Cage Bars
• Bearings: Heavy duty Ball and Roller bearings are fitted for maximum life and low noise operation
• Compressing: Crammer Shaft gives extra Cramming of the seed or cake in the Feed
• Shaft Withdrawal: The main Worm Shaft can be withdrawn very easily without disturbing the gear section in any way. Pressing worms and collars can be changed without disturbing the main shaft. The thrust of the pressure worms is taken upon large spherical roller thrust bearings
• Easy to install, high yield at low operating cost, capable of extracting oil from all known oil seeds
• Reduced internal wear and tear
• Best Quality of Oil & Cake
• Maintenance is less & easy
• Hardened Worm Assembly
• Cast Iron Bodies: For perfect alignment and stability
• Steel Fabricated Base

Chamber	Fabricated chamber
Automatic Grade	Automatic, Semi-Automatic
Capacity	8/10 tons in first pressing and 5/6 tons in second pressing
Power	3 Phase 50 hp Motor

• Chambers: Reduces time and labour for relining of Cage Bars
• The main Shaft of the Expeller is of alloy steel construction, fitted with High Pressure Worms, hard faced, with a highly wear resistant alloy
• Shaft Withdrawal: The main Worm Shaft can be withdrawn easily without disturbing the gear section. The thrust of the pressure worms is taken upon large spherical roller thrust bearings
• Gear Box & Lubrication: An improved triple helical parallel shaft gear unit made from most suitable special steel, running in oil bath. All shafts run on antifriction bearings. Drive housing is oil tight and dust proof, totally enclosed design and is fitted with level indicator. A self contained lubrication arrangement has been provided
• Kettle / Cooker: Multistage vertical stack cooker for proper conditioning of the seeds
• Lower Power Consumption: The Selection of motors is done keeping in mind the peak load that could arise due to inconsistent feeding resulting in lower power consumption
• Premium expelled Oil Quality: Well designed worm assembly and chamber construction ensures superior quality of expelled oil
• Superior Quality of Cake: The cake quality is excellent and cake produced from the machine is of natural color without charring or burning effect
• Retention of oil in Cake: Superior process parameters ensure accurate retention of oil in the cake

Automatic Grade	Automatic, Semi-Automatic
Usage	Soybean Oil, Peanut Oil, Sunflower Oil, Cotton Seed Oil
Material	Steel, Cast Iron
Machine Type	Extracting Machine